High Power Collimated 405nm UV Laser Diode Module Up to 1.5W Sharp GH04W10A2GC

Description

High Power Collimated 405nm UV Laser Diode Module Up to 1.5W Sharp GH04W10A2GC
High Power Collimated 405nm UV Laser Diode Module Up to 1.5W Sharp GH04W10A2GC
These modules were extracted from high brightness laser phosphor video display units. Each module includes
Sharp GH04W10A2GC multi-mode 405nm laser diode pressed into a copper heat spreader
Glass aspheric collimating lens, similar to the popular G-2 and AR coated for extremely low loss at 405 nm.
Anamorphic correction lens
AR coated glass block that can be rotated by a tiny stepper motor to shift the beam left/right by a few mm.
The laser diode is in a standard 5.6mm can which has been pressed into a copper heat spreader. The diode leads are isolated from the case and the polarity is shown in one of the pictures. The diode can be easily removed by bending the soft copper heat spreader. These are multimode lasers which are rated for 350mW CW and 1100mW pulsed, but are quite capable of being overdriven.  We test each unit - briefly at 1250mA to make sure it has lots of headroom and again at 1000mA to check the operating power.  These diodes are guaranteed to produce 1.5W or better at a maximum of 1.1A drive current. The chart also shows a typical 16X Blu-ray diode performance for comparison. The wavelength shifts up to 410-412 nm when run at 1.5W.
There is some sort of driver board on the back of the module, but it has an unusual interface so you will need to replace that with your own laser diode driver suitable for producing 1A with a diode compliance voltage of 5.0V. We don't stock this sort of driver, but they are easy to find from other sellers on eBay. Board pinout and partial schematic will be provided to buyers on request.
The collimating lens is AR coated specifically for 405nm so it is extremely low-loss.  It is glued into the module and pre-collimated.  If you want to remove it for use in another type of module, just heat up the epoxy with a hot air gun and press it out with something soft like a q-tip. You can see the extracted lens in the last picture.
The anamorphic lens corrects the multi-mode output from a 25mm x 4mm stripe at 10 meters to a 25mm diameter round spot at 10 m (see pictures).  This works out to a divergence of about 2.5mrad.  The beam exiting the module is about 4 x 1 mm so suitable for knife-edge combining. This does not make as tight a beam as a single-mode diode, but the circularized beam should focus down to a small, round spot for cutting and etching applications. These should also be ideal for UV cured resin based 3D printers.
The final stage of optics is an easily removable block of AR coated glass that can be rotated with a tiny, built-in stepper motor.  This allows the beam to be offset a few mm left or right without changing the aiming.  This might be ideal for knife-edge combining.
The last picture shows one of the modules fully disassembled. Check out other listings if you'd prefer a tested, extracted diode ready to install in your own host.
Pictures and description Copyright © 2020 Starlight Photonics, Inc.
Starlight Photonics Policies
FDA Disclaimer for Laser Items
This product is sold solely for use as a component (or replacement) in an electronic product; therefore it is not required to, and does not comply with, 21 CFR 1040.10 and 1040.11 which pertain to complete laser products. The manufacturer of the complete system-level electronic product is responsible for complying with 21 CFR 1040.10 and 1040.11 and for providing the user with all necessary safety warnings and information.
Payment
Payments are handled by eBay Managed Payments which allows a variety of payment methods such as credit, debit, and gift cards, Apple Pay, Google Pay, PayPal, and PayPal Credit. We accept Purchase Orders from accredited Universities. Please note that sales tax is collected by eBay, not by the seller. To avoid paying sales tax, you need to have your reseller certificate on file with eBay
before making a purchase
.
Shipping
All orders will be shipped within 3 business days of receiving payment. Most orders will be shipped much sooner than that. Please check the Shipping and Payments tab on the auction listing to see the carrier and cost for shipping. We take pride in our careful packing of delicate items. In the unlikely case that you receive an item which has been damaged in shipping, please hang on to the packing material and contact us. We will file a damage claim with the shipper and start the process of getting you a replacement or a refund.
Warranty
Items we sell on eBay do not include any warranty unless otherwise specifically stated in the listing. We do guarantee that the items we sell will be delivered in the condition described in the listing and pictures. If you have a problem with your purchase, please get in touch and we'll do our best to get things working.
Return Policy
We generally do not accept returns for items sold on eBay. Please read the listing carefully, do your research and ask us any questions you need to decide if the item is suitable for your use. We will occasionally make an exception for items which are
still in the sealed package and are returned along with all the original accessories, paperwork and packaging. Shipping charges are not refundable and opened packages will incur a fee to cover testing and restocking the item. Returns which are not resalable due to missing parts, damage, alteration, etc. will not be refunded.
International Sales
Orders shipped by eBay Global Shipping Program (GSP) include import charges in the order price. For orders shipped by other carriers, import duties, taxes, and other charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. We will not falsify export documentation.
Company Information
Starlight Photonics, Inc.
PO Box 1134
Alviso, CA 95002